福州天心緣科技有限公司是一家***為國內外鋼鐵廠提供優質的熱金屬檢測器等冶金配件的企業，為上百家鋼鐵廠提供滿意的服務。
    公司主營產品熱金屬檢測器繼承了傳統的工業級元件，對核心部件進一步升級，采用的是***級元件。產品更加穩定，適應于鋼鐵廠高溫的環境。十年的技術積累，鑄就***的產品質量?？煽康漠a(chǎn)品和周全的***服務讓客戶放心！

***網站：http://

棒材冷床熱金屬檢測器

  在軋鋼生產線上，棒材冷床是整條生產線上的關鍵部分，而熱金屬檢測器（熱檢探頭、紅外線檢測器）又是棒材冷床的重要檢測站，熱金屬檢測器的溫度檢測范圍寬、穩定性好是軋鋼產量和成材率的根本保障。

  新一代棒材冷床熱金屬檢測器HMD4、HGE98、HGE65、RJJ4、RJJG型在傳統檢測器的安裝尺寸、接線編號的基礎上進行升級。機芯采用進口元件、檢測頭采用多角度顯微鏡鏡片和大口徑耐高溫工藝玻璃防塵，使檢測范圍更寬。檢測器帶有現場電源變色指示燈、高溫警示燈、實驗按鈕和可靠的航空插頭電線電纜，在現場具有穩定性好，操作維修方便等特點。

1.工作原理

  本檢測器接收到鋼的運動信號，經光學部分進行聚焦到光學元件上后經電子線路處理，輸出兩對開關量，繼電器觸點輸出和無觸點電平輸出，實現冷床一個站點的監控。

2.技術指標                            

—接收光譜范圍：400nm-1100nm                 

—檢  測 溫 度：260℃-1400℃                   

—響  應 時 間：接點﹤20ms 電接點﹤2ms 

—檢  測 距 離： 0.03m-1m

—工  作 溫 度：–25℃－75℃（帶風冷）、 –25℃－100℃（帶水冷）

—儲  存 溫 度：–25℃－70℃

—電  源 電 壓：AC220V&plu***n;20％ 、 DC24V

—防  護 等 級：IP67

—自  檢 功 能：按實驗按鈕，可檢查出接點、電接點是否正常

—廣  角 透 鏡：采用顯微鏡鏡片，讓視角更寬

—光  電 元 件：采用進口高靈敏度VXT***80

—變 色 指示燈：電源指示綠色、工作動作指示紅色    

—冷     卻：水冷裝置，可采用氧氣管作水管，幾個檢測器串接起來同時冷卻

—體     積：310mm（長）×200mm（高）×56mm（厚）

—重     量：2.10千克

3.使用方法

  紅鋼運動范圍在檢測中的視場范圍內，然后上下左右調整檢測器，使鋼在檢測器視場范圍內的中間位置即可保證可靠工作，***后固定檢測器。

4.接線表

接線表1（適用于HGE98、HGE95、HMD4、RJJ4、RJJG - DC24V型）

接線表2（適用于HGE65、HGE95、HMD4、RJJ4、RJJG - AC220V型）

5.注意事項

①請不要在太陽光直射到的地方安裝檢測器，做好防止陽光及其他光線的干擾；

②在周圍環境達到70℃以上時必須加水冷卻；

③檢測器使用一段時間后，請擦除防塵筒內平凸透鏡上的灰塵等雜物，如靈敏度有下降，請調節檢測器的靈敏度。

福州天心緣科技有限公司

聯系電話/微信：13959160696，15985729698

E-mail：fztianxinyuan＠

地址1：福州市臺江區江濱中大道378號海潤花園23幢203室（臺江萬達廣場旁）

地址2：福建省福州保稅區綜合大樓15層A區-5071（自貿試驗區內）

英文說明：

Hot metal detector

  In the rolling steel production line, the cold bed is the key part of the whole production line, and the hot metal detector (thermal detector, infrared detector) is an important inspection station of the cold bed. The wide temperature detection range and the fine stability are the fundamental guarantee of the rolling steel output and yield.

  These new generati*** of hot metal detectors HMD4, HGE98, HGE65, RJJ4, RJJG-type are updated from the traditional in aspects of installation dimension and Connection number. Imported components are used in electronic circuits. In the detecting head, the multi-angle microscope lens and the large-diameter heat-resistant dustproof glass are introduced. All these improvements make the detection range wider. The detectors are equipped with color-change indicator, high-temperature warning indicator, test button and reliable ***iation plug, electric wires and cables, which h***e the characteristics of stability, easy-use, easy-maintenance, etc.

1. Working principle

  The hot metal detector receives a light signal from the moving steel. The light is concentrated on the optical component. After the signal is processed by electronic circuits, two kinds of switches are outputted: relay passive contact output and contactless active high level output, which implement the monitoring of one station on the cooling bed.

2. Technical parameters

— Detected spectral range: 400nm-1100nm

— Detected temperature: 260℃-1400℃

— Resp***e time: contact < 20ms; electric contact < 2ms

— Detected distance: 0.03m-1m

— Working temperature: –25℃－75℃ (air-cooling); –25℃－100℃ (water-cooling)

— Storage temperature: –25℃－70℃

— Power voltage: AC-220V&plu***n;20％; DC-24V

— Level of protection: IP67

— Self-checking: Press the test button and check if the contact or electric contact is normal.

— Wide-angle lens: microscope lens widening the visual angle of devices

— Photoelectric element: imported VXT***80 with high sensitiity

— Color-change indicator: green (power supply); red (working)

— Cooling: For water-cooling devices, oxygen hoses can be used as water hoses and several detectors can be concatenated to be cooled together.

— Size: 310mm × 200mm × 56mm (length × height × thickness)

— Weight: 2.10kg

3. How to use

  Put the detector in a position where the movement of the hot metal is within the range of detection. Then adjust the direction of the detector to make sure that the hot metal is at the center of detection range. In the end, immobilize the detector.

4. Wiring tables

Wiring table 1 (applicable to HGE98, HGE95, HMD4, RJJ4, RJJG - DC24V)

Wiring table 2 (applicable to HGE65, HGE95, HMD4, RJJ4, RJJG - AC220V)

Note: COM = common point, NO = normally open, NC = normally close.

5. Cauti***

① Please do not install the detector in the position radiated by the sunlight directly. Prevent disturbances of sunlight and other possible lights.

② Water-cooling is a must when the environment temperature exceeds 70℃.

③ After a period of usage time, please wipe the dust or dirt on the lens which is hidden in the dustproof cylinder. If the sensitivity is declined, please adjust the sensitivity knob.

???????