東曹PPS SGX-140---TOSOH is a global chemical and special materials company. The company was established in 1935 as Toyo Soda Manufacturing Co.,  in Yamaguchi, Japan, and changed its name to Toyo Soda Manufacturing Co.,  in 1987. Today, the company is headquartered in Tokyo, Japan.

PPS注塑技術參數 
干燥溫度（℃） 120～130 干燥時間約（hr） 2～3  
模具溫度（℃） 85～140（加隔熱板） 殘 料 量（mm） 3～10  熔膠溫度（℃） 300～340 背 壓（MPa） 5～12  注she壓力（MPa） 100～150 鎖模力約（ton/in2） 4～5  注 塑 速 度 中速至高速 回 料 轉 速(rpm) 60～80  螺 桿 類 別 標 準 螺 桿（直 通 式 噴 嘴）  停 機 處 理 關料閘啤清即可 碎料翻用（%） 20～30 
*1、20%玻璃纖維增強PPS（PPS+20%GF)：耐高溫，高光澤，高流動； *2、30%玻璃纖維增強PPS（PPS+30%GF)：耐高溫、標準級；  
*3、30%玻璃纖維增強PPS（PPS+30%GF增韌)：高韌性，高光澤，高流動，耐低溫耐寒； 
*4、40%玻璃纖維增強PPS（PPS+40%GF)：耐高溫、標準級； 
*5、40%玻璃纖維增強PPS（PPS+40%GF增韌)：高韌性，高光澤，高流動，耐低溫耐寒；  
*6、65%玻纖/礦物增強填充PPS（PPS+玻纖/礦物）：高電氣性能、低成本 ； *7、30%玻纖增強PPS+鐵氟龍（PPS+30%GF+PTFE)：自潤滑、低摩擦，高耐磨； 
*8、40%玻纖增強PPS+鐵氟龍+石墨（PPS+GF+PTFE+石墨）：自潤滑、超耐磨； 
*9、20%玻纖+20%碳纖+鐵氟龍（PPS+GF+CF+PTFE) *10、20%二硫化鉬+鐵氟龍（PPS+MoS2+PTFE）

Testing or identification of Plastics:  
 The density of unreinforced PPS was 1.4 GCM ˉ3, The guild sinks rapidly in water and slowly in saturated magnesium chloride solution (density is 1.34); The density of PPS containing 40% GF was 1.6 GCM ˉ3. The fiber content can reach 45%. When mineral filler and glass fiber are used together, the total filler content can reach 65% (by weight)
Treatment of plastics and products:  
 However, heating is good for processing, so all materials should be dried. It is best to dry them in a dehumidifier (175 ℃) at 150 ℃ for 3 hours - even in an ordinary oven for 6 hours Hardness, crystallinity and HDT above 260 ℃  
 Generally speaking, the hot mold (above 135 ℃) can produce enough crystallinity and excellent surface. However, if the product is not required to be heat-resistant and stable, the cold mold (30-90 ℃) can be used. The HDT of such (low crystallinity) products may only be 230 ℃. The surface of the parts may be poor, It can be dried at 150 ℃ for 3 hours